Autel 808 Series Update: Adds Active Test+ Battery Test + Digital Inspection

Autel adds Active Test, Special Function, battery test and active test on Autel 808 series tablet on June 1st, 2022. You can obtain all new software packages by tapping ‘Update’ icon on the Autel scan tool. Make sure the device’s system version is updated to V2.62 or above. If there is not enough storage for downloading update, just insert a micro SD card to the Autel device.

 

Part One: Active Test and Special Function

autel 808 series tablet special function update 1 - Autel 808 Series Update: Adds Active Test+ Battery Test + Digital Inspection - Autel 808 Series Tablet Special Function Update

Definition:

  • Active Test function is used for outputting signal to vehicle control unit using the device to control actuator for test, so that it can test whether the actuator works normally, such as Fuel Pumps test, EGR test, etc.
  • Special Function generally refers to the initial adaptation, self-learning or some auto detection function with many procedures that the vehicle is performed after maintenance or reset is done or some related component in electronic control system is replaced, such as Crankshaft Position Sensor Learn.

 

Compatible device:

Autel MX808, MX808TS, MK808, MK808BT, MK808TS, TS608, IM508

(Applies to Autel devices above in all regions except mainland China)

 

Vehicle coverage:

All vehicle brands that the device can support

 

Step-by-step guide:

  • Perform Active test Function
  1. Read vehicle by auto detect, manual input or manual selection;
  2. Select Auto scan or Control Unit —– (Powertrain/Body/Chassis) —- relevant module—Active test;
  3. Take steps by following the on-screen instructions.
  • Perform Special Function:
  1. Read vehicle by Auto detect or manual input or manual selection;
  2. Select Auto scan or Control Unit —– (Powertrain/Body/Chassis) —- (relevant module) —Special function;
  3. Take steps by following the on-screen instructions.

 

Part Two: Battery Test

autel 808 series tablet special function update 2 - Autel 808 Series Update: Adds Active Test+ Battery Test + Digital Inspection - Autel 808 Series Tablet Special Function Update

Definition:

Battery Test function includes In Vehicle test and Out of Vehicle test function.

  • In-vehicle Test is used for testing batteries that are installed in a vehicle. An in-vehicle test includes battery test, starter test, and generator test. These tests help determine the health status of the battery, the starter, and the generator, respectively.
  • Out-vehicle test is used to test the condition of batteries that are not connected to a vehicle. This function aims to check the health status of the battery only

autel 808 series tablet special function update 3 - Autel 808 Series Update: Adds Active Test+ Battery Test + Digital Inspection - Autel 808 Series Tablet Special Function Update

Compatible device:

MK808BT, MX808TS, DS808BT, DS808TS, MP808BT and MP808TS

(Applies to Autel devices above in all regions except mainland China)

 

Additional equipment is required:

Autel MaxiBAS BT506

autel 808 series tablet special function update 4 - Autel 808 Series Update: Adds Active Test+ Battery Test + Digital Inspection - Autel 808 Series Tablet Special Function Update

 

Step-by-step guide:

  • Perform the In-vehicle battery test

Note: The complete in-vehicle test includes battery test, starter test and generator test, in sequence.

  1. Battery Test
  2. a) Connect MaxiBas BT506 with tablet device
  3. b) Tap the Battery Test application on the Autel tablet menu
  4. c) Tap In-vehicle test
  5. d) (Optional) Establish communications between the VCI and vehicle by following the on-screen instructions on the OBD connect screen.

NOTE: OBD connect is recommended and is used for automatically obtain battery type and location.

  1. e) Confirm the vehicle information. The vehicle information screen automatically displays when vehicle communication is established. A Battery location button will pop up from the bottom of the screen.
  2. f) Tap Next and access the Battery tab. Perform required operation before the battery test based on the on-screen instructions. And tap the Start Testing button
  3. g) Wait for the battery test to complete and view the test results

 

  1. Starter Test
  2. a) Tap Continue. Perform required operations before the battery test based on the on-screen instructions. And tap the Start Testing button
  3. b) Turn on the vehicle ignition to ON when the following screen appears
  4. c) Wait for the test to complete and view the test results

 

  1. Generator Test
  2. a) Tap Continue. Perform required operations based on the on-screen instruction
  3. b) Tap Continue and view the test results

 

  • Perform the out-vehicle battery test
  1. a) Connect MaxiBas BT506 with tablet device
  2. b) Turn on MaxiBas BT506 and connect it to the battery
  3. c) Tap the Battery Test application on the Autel tablet Job Menu
  4. d) Tap Out-vehicle test
  5. e) Check the battery information and tap Start Testing
  6. f) Wait for the battery test to complete and view the test results

 

Check battery test report:

Path 1: Tap ‘Report’ button at the end of each test to check the test report

Path 2: Go to Data Manager>>Vehicle Information>> Battery Test to check the test report after a test is completed

 

Part Three: Digital Inspection

autel 808 series tablet special function update 5 - Autel 808 Series Update: Adds Active Test+ Battery Test + Digital Inspection - Autel 808 Series Tablet Special Function Update

Definition:

The Digital Inspection application configures the Autel 808 series Diagnostics Device to operate as a digital video scope by simply connecting the tablet to a Digital Inspection Camera. This function allows you to examine difficult-to-reach areas normally hidden from sight, with the ability to record digital still images and videos, which offers you an economical solution to inspect machinery, facilities, and infrastructure in a safe and quick way.

 

Compatible device:

Autel MK808, MK808BT, MK808TS, MX808, MX808TS, MP808, MP808BT, MP808TS, DS808, DS808BT, DS808K, DS808TS

(Applies to Autel devices above in all regions except mainland China)

 

Additional equipment is required:

Digital Inspection Camera MV105/MV108 and its fittings

autel 808 series tablet special function update 6 - Autel 808 Series Update: Adds Active Test+ Battery Test + Digital Inspection - Autel 808 Series Tablet Special Function Update

 

Step-by-step guide:

1.Take images using the Digital Inspection application

  • Connect the imager head cable to the USB port on the top of the tablet.
  • If not already done, power up the tablet.
  • Tap the Digital Inspection application on the Autel scanner menu.
  • The Digital Inspection interface displays, showing a camera operating screen. The imager head camera is used by default.
  • Select the Camera icon at the lower-right corner to take images.
  • Focus the image to be captured in the view finder by adjusting and properly locating the imager head cable.
  • Tap the blue ring on the screen. The view finder now displays the captured picture and auto-saves the taken photo.
  • Tap the thumbnail image on the top-right corner of the screen to view the stored image. Slide the screen left and right to view the images.
  • Tap on the selected image and the edit toolbar instantly displays.
  • Tap the corresponding button to share or delete an image.
  • Tap the Back or Home button on the Navigation Bar at the bottom of the screen
  • Exit the Digital Inspection application

 

2.Record a video using the Digital Inspection application

  • Connect the imager head cable to the USB port on the top side of the tablet.
  • If not already done, power up the tablet.
  • Tap the Digital Inspection application on the Autel scan tool. The Digital Inspection interface displays, showing a camera operating screen. The Imager head camera is used by default.
  • Select the Video icon at the lower-right corner to record a video.
  • Properly locate the imager head cable to focus the inspection scene for recording.
  • Tap the red ring on the operating screen to start recording.
  • Tap the red circle again to stop recording. The recorded video is automatically saved.
  • Tap the gallery icon at the bottom-right corner to review all recorded videos.
  • Select the corresponding button on the upper-right corner to search or delete a video.

 

www.obdexpress.co.uk

(Visited 130 times, 1 visits today)
favicon - Autel 808 Series Update: Adds Active Test+ Battery Test + Digital Inspection - Autel 808 Series Update: Adds Active Test+ Battery Test + Digital Inspection