Fixed! KTM Bench identified Bosch MEDC17 ECU failure

June 24, 2020 sales Car ECU programmer 0

One user feedback: I have KTM Bench ECU programmer to test with different ecms

And always with the same message “Bosch MEDC17 (TC1724 /1728 / 1767 / 1782 / 1784 / 1797) Flash identification, entering reprogramming mode failure”

I have tested the same connection with another j2534 interface

And can connect with ecm obviously can’t read

the ecu type is 1766.

 

Attach several images of the Bosch ECU type & its internal pcb, the connection diagram, the error messages:

fixed ktm bench identified bosch medc17 ecu failure 01 - Fixed! KTM Bench identified Bosch MEDC17 ECU failure - Fixed Ktm Bench Identified Bosch Medc17 Ecu Failure 01 fixed ktm bench identified bosch medc17 ecu failure 02 - Fixed! KTM Bench identified Bosch MEDC17 ECU failure - Fixed Ktm Bench Identified Bosch Medc17 Ecu Failure 02 fixed ktm bench identified bosch medc17 ecu failure 03 - Fixed! KTM Bench identified Bosch MEDC17 ECU failure - Fixed Ktm Bench Identified Bosch Medc17 Ecu Failure 03 fixed ktm bench identified bosch medc17 ecu failure 04 - Fixed! KTM Bench identified Bosch MEDC17 ECU failure - Fixed Ktm Bench Identified Bosch Medc17 Ecu Failure 04 fixed ktm bench identified bosch medc17 ecu failure 05 - Fixed! KTM Bench identified Bosch MEDC17 ECU failure - Fixed Ktm Bench Identified Bosch Medc17 Ecu Failure 05

 

obdexpress.co.uk engineer solution:

The cpu is tc1767,but you connect as tc1766,so your connection is wrong.

 

Finally, the problem is solved!

 

Here BOSCH MEV17.4.2 IROM TC1767 PSA 1033:

PLUGIN 286

fixed ktm bench identified bosch medc17 ecu failure 06 - Fixed! KTM Bench identified Bosch MEDC17 ECU failure - Fixed Ktm Bench Identified Bosch Medc17 Ecu Failure 06

fixed ktm bench identified bosch medc17 ecu failure 07 - Fixed! KTM Bench identified Bosch MEDC17 ECU failure - Fixed Ktm Bench Identified Bosch Medc17 Ecu Failure 07

 

DIRECT CONNECTION WITH TRASDATA SYSTEM

In order to perform the Trasdata direct connection with free wirings it will be necessary to

connect the POL4 pin and DSDO signal too. DSDO is the yellow wire on BDM connector of the

universal adapter F34TD003.

fixed ktm bench identified bosch medc17 ecu failure 08 - Fixed! KTM Bench identified Bosch MEDC17 ECU failure - Fixed Ktm Bench Identified Bosch Medc17 Ecu Failure 08

 

DIRECT CONNECTION WITH NEWGWNIUS SYSTEM

In order to perform the NewGenius free wires connection you need the F32GN037

or F32GN037-B cable. BLUE wire = CNF1, GREY wire = BOOT

fixed ktm bench identified bosch medc17 ecu failure 09 - Fixed! KTM Bench identified Bosch MEDC17 ECU failure - Fixed Ktm Bench Identified Bosch Medc17 Ecu Failure 09

 

DIRECT CONNECTION

fixed ktm bench identified bosch medc17 ecu failure 10 - Fixed! KTM Bench identified Bosch MEDC17 ECU failure - Fixed Ktm Bench Identified Bosch Medc17 Ecu Failure 10

 

DIMA CONNECTION

Connect the 2 boot pin to the programming lay-by pin n. 10. Moreover it is necessary to

solder a third wire that must be connected to the CNF1 clamp on the DIMA.

fixed ktm bench identified bosch medc17 ecu failure 11 - Fixed! KTM Bench identified Bosch MEDC17 ECU failure - Fixed Ktm Bench Identified Bosch Medc17 Ecu Failure 11

fixed ktm bench identified bosch medc17 ecu failure 12 - Fixed! KTM Bench identified Bosch MEDC17 ECU failure - Fixed Ktm Bench Identified Bosch Medc17 Ecu Failure 12

fixed ktm bench identified bosch medc17 ecu failure 13 - Fixed! KTM Bench identified Bosch MEDC17 ECU failure - Fixed Ktm Bench Identified Bosch Medc17 Ecu Failure 13

Credits to www.obdexpress.co.uk

 

(Visited 536 times, 1 visits today)
favicon - Fixed! KTM Bench identified Bosch MEDC17 ECU failure - Fixed! KTM Bench identified Bosch MEDC17 ECU failure

who like this article also viewed: