How To Update K Suite Kess V2 2.25 2.28 Software Step Guide and video
Obdexpress engineers has verified that K Suite software v2.25- v2.28 can work OK with kess v2 .It works well on SE87 ,SE87-C,SE87-E,SE87-K and SE86-CK Here is how to […]
Car ECU programmer
Why i need to buy Galletto 4, Kess v2 and Ktag together?
Kess v2, Ktag, Fgtech Galletto 4 are the top 3 ECU programmers in the market. Ever failed on some ECUs? Actually, it’s necessary to buy […]
How To Solve UPA USB V1.3.0.14 “usb device not recognized”
Customer puzzle: Does someone has dump for 24lc128 eeprom v1.3r2? My UUSP upa was working fine, and today it say’s usb device not recognized, I […]
How to get UPA USB programmer v1.2 work with UPA-USB v1.3 software
It’s a customer solution of how to rework yellow upa usb programmer v1.2 to green upa usb programmer v1.3.0.14 It’s old version upa programmer […]
Fgtech galletto 4 v54 OK to read & write bmw edc17?
Is it ok to buy Fgtech galletto 4 v54 to read and write BMW ECUs? To work with edc17 without issues? Here goes to questions […]
MPPS v21 v18 v16 v13 software download
This clone MPPS tools are a 1:1 of the original. Here download the crack mpps software v21 v18 v16 v13 with buying cables together. […]
MPPS V18 eu clone hardware & mpps software review
This is MPPS V18 clone review from diy users at http://www.obdexpress.co.uk/. Part 1- review on MPPS V18 cable: The cable is a […]
(solved) Xprog-m v5.5.5 “verify error” fixed by Xprog v5.51
Here are important tips for all xprog users when they got this problem “verify error” during reading motorola mcu, and after try several time is […]
Yanhua MB CAN Filter 18 in 1 User Manual
It’s a user manual of Yanhua Mercedes-Benz CAN filter 18 in 1, including installation/connection instruction and vehicles available. How to use YH MB CAN […]
How to do when you lift pin 55 on Carprog
Now I have succeeded in one Carprog unit(CARPROG FULL V9.31), with help of a sewing needle. It will go wrong because I get up two […]
Rework Ktag Kess V2 pcb hardware-no issue
Share free solutions of reworking clone Ktag and Kess V2 ECU tuning tools to work completely like the genuine. Original PCB in the photo … […]
Which ECU programmer better, Xprog-m or UPA-USB?
People talks a lot on XPROG-M and UPA at forum,Which better? any difference of them? This post make a detail comparison table of X-prog m […]
How to reset BMW airbag with Carprog v8.21 v9.31
It just takes 1 minute to reset and repair airbag computer in your office, with the new CarProg v8.21 or CarProg v9.31 airbag reset tool. […]
How to reflash CARPROG MCU AT91SAM7S256
Here is a experience from DK forum members who made this possible about how to reflash CARPROG Mcu AT91SAM7S256 Tool use: Carprog clone v8.21 firmware We need […]
(solved) Xprog-m Xprog-box v5.55 Safengine error”□□□□”
When i installed Xprog-m v5.5.5 software, the Safengine error □□□□ popped up Solved by professional technicians! Open Computer Management and the find out ET199 […]
How to solve Carprog v8.21 Unit CRC error (delete LIB file)
Here is a customer solution of Carprog v8.21 with the following error message: Unit CRC error: Delete LIB file and make UPDATE -> INTERNET A1 […]
Checksum Family Manual for ECM Titanium v1.61
What is Checksum? Checksum is the security algorithm with which are encoded files stored inside the engine control units; if the modified files you are […]
V54 FGTech Galletto 4 wiring diagram for BMW Bosch EDC17 MEVD17
Here is the FGTech BOOT Tricore user manual for BMW ECU Bosch EDC17 and MEVD17, wiring diagrams attached also. BMW ECU here includes: Bosch EDC17 […]
How to use KTAG KTM100 to read BMW F10 EDC17C41 [tips]
Here are some tips of “reading error” for you when reading EDC17C41 DDE8 520d F10 ecu with Ktag clone, offered by experienced users. TRY OWN […]
FGtech Galletto 4 vs CMD flasher vs Alientech Ktag Kess v2 vs MagPro
Invested on Chinese ECU programmers, FGtech Galletto 4, CMD flasher v1251, clone Alientech (Ktag and Kess v2), MagPro x17… I read a lot, with each […]
