OBDSTAR ODO Master Cluster Calibration confirmed: 2014 Renault Meganne Mk3
Confirmed: OBDSTAR ODO Master is capable of performing cluster calibration for 2014 Renault Meganne Mk3. Here are the ODOMaster supported dashboard types: 24C16 Dash […]
Month: August 2021
How to program a used ECU for Nissan kicks with Autel IM508?
Problem: used Autel IM508 to program a used ECU for Nissan kicks with new blade keys, it refuses to be programmed and only register them […]
Launch X431 ProS Mini: Porsche Cayenne 9Y0 2020 service reset
Car model and year: Porsche Cayenne 9Y0 2020 with 30,000 miles Purpose: to do service reset Update: Got all the tools. BMW uses […]
Autel MaxiIM IM608 renew Mercedes ECU engine 111 Successfully
Autel MaxiIM IM608 is capable of renewing Mercedes ECU engine 111 Successfully. . I do not need to read the data from the old ecu […]
Is there no online function for X431 PAD 7? How to configure X431 PAD 7 online programming?
Written in front: Launch X431 PAD 7 includes online programming function, but it is not turned on by default, and this function is not supported […]
How to fix VXDIAG VCX SE IDS “Checksum firmware failed”?
Used VXDIAG VCX SE to run Ford IDS, got error “Checksum firmware failed!”, look at the following images. How to solve? All can work no […]
BMW F20 2013 95128 Cluster Calibration Tools Advice and Guide
Problem: there is a BMW F20 2013 with FEM module. There will be an engine replacement with much less km on it. So want to […]
ECU clone tools for most cars needed
Topic: looking for the ECU cloning tools for most cars, I wanna read out cs number and pincode for immobilizer. I think if I need […]
Autel IM608 AKL programming: 2020 Subaru Impreza
Autel IM608 Success: 2020 Subaru Impreza push start ign all keys lost 16 min in and out with 2 new smart keys Don’t you […]
How to determine if IM608 can use IMMO function in your car
To check Autel IM608 “key programming” function or “IMMO part replacement” function is supported your car or not, you can go to function viewer APP […]
Xhorse VVDI Key Tool Plus wiring diagram (SCL pin 1, SDA pin 11)
Xhorse VVDI Key Tool Plus does not have the diagram of SCL pin 1 SDA pin 11. I would like to share below. (Key Tool […]
Xprog 5.5.5 read atmega64a IC: confirmed
I managed to flash with Xprog 5.5.5 software, it is giving error when trying to read but it is able to ind device in xprog […]
Clone sim4lke with MPPS and Kess: Confirmed
Have sim4lke ECU to clone, look at the photos of the ECU below. Suggestion: SIM4L KE 5WK90526 A2711538579 A0014466902 Take car that all numbers […]
Motor Angle Calibration with X431 PAD VII, European Euro Tab III, MM4.0 etc
Any of Launch X431 PAD VII, European Euro Tab III, MM4.0 (other devices can buy “Motor Angle Calibration” function in Mall module) can calibrate the […]
Dont buy Xprog Clone 6.17, Just buy Xhorse VVDI Prog
Xprog Clone 6.17 is popping up on eBay and several other sites, it really didn’t last long, Was brand new and untouched, set up on […]
Launch X431 Frequently Asked Questions and Solutions
Launch X431 diagnostic tools are generally based on the Android operating system, and the tablet models and menu names of different devices may be inconsistent, […]
Launch X431 V 8inch Service Reset Function Vehicle Coverage
Launch X431 V 8inch Tablet full-system diagnostic scanner can perform the service reset functions for hundreds of car makes. In addition to amazing & powerful […]
Super MB Pro M6, any better than MB sdconnect C4 Plus DoIP / C4 / C6?
Comparison table: Super MB Pro M6 vs. MB SD C4 vs. SD C4 DoIP vs. OEM MB C6 Super MB Pro M6 (SP369) MB SDConnect […]
How to solve Golf 7 MQB remote not start car? With Xhorse VVDI2?
Problem: First time I repair an MQB remote. Remote key start engine but no light or frequency go out. After repair pcb, light go […]
Xentry 03/2021 error “The data are faulty” Solution
Xentry 03/2021 can’t connect and error “The data are faulty”. During the past months, some users feedback this problem, and someone tested and worked out […]
