Buick 2008 GL8 Firstland Service Programming System (SPS) with J2534 Vxdiag

Confirmed: J2534 Vxdiag Nano can perform online Service Programming System (SPS) on many GM /Opel car models, like Buick 2008 Passenger car GL8 Firstland (C) 3.0L V6 LZC. This article is available with the whole procedure.

 

Car info:

Buick 2008

Passenger car

GL8 Firstland

(C) 3.0L V6 LZC

 

Controller:

ECM: Engine Control Module – Programming (Pass -Thru Only)

TCM: Transmission Control Module

PSDM: Power Sliding Door Module – Programming

CCP: Climate Control Panel – programming

 

Purpose: Reprogram (Normal not VCI)

 

Using:

J2534 Vxdiag Interface

Login ACDelco for subscription of Service Programming System (SPS)

j2534-vxdiag-reprogram-buick-2008-01

 

Procedure:

Login ACDelco TDS.

Click on “Service and Programming Information”.

Choose ” Service Programming Only” and click on “Access your subscription”.

j2534-vxdiag-reprogram-buick-2008-2

 

Click on “OK”.

j2534-vxdiag-reprogram-buick-2008-3

 

Click on “Service Programming System (SPS)”.

j2534-vxdiag-reprogram-buick-2008-4

 

Click on “Start SPS” and it will automatically launch Java 6.

j2534-vxdiag-reprogram-buick-2008-5

 

Skip software installation of Tech2 J2534 Driver.

j2534-vxdiag-reprogram-buick-2008-6

 

Select “J2534 VXDIAG” – “Reprogram ECU“, then “Next“.

NOTE :As for reprogramming with J2534 MDI or with Tech2, the procedure is the same.

j2534-vxdiag-reprogram-buick-2008-7

 

Read messages “Connect J2534 device to vehicle and PC”.

j2534-vxdiag-reprogram-buick-2008-8

Select Buick car info.

Confirm car VIN.

j2534-vxdiag-reprogram-buick-2008-9 j2534-vxdiag-reprogram-buick-2008-10

 

Select ” ECM: Engine Control Module – Programming (Pass -Thru Only)”, then “Normal”.

Configuration succeed.

j2534-vxdiag-reprogram-buick-2008-11 j2534-vxdiag-reprogram-buick-2008-12

 

Click on “Next” and then “OK” to reprogram with the same calibration.

j2534-vxdiag-reprogram-buick-2008-13

 

Transfer data.

1). Download from server

2). Load to ECU.

It may take a long time to finish, please ensure the computer not sleep.

3). Programming complete.

j2534-vxdiag-reprogram-buick-2008-14 j2534-vxdiag-reprogram-buick-2008-15

 

Click on “New”, then “Next”, select ” TCM: Transmission Control Module”, then “Normal”.

j2534-vxdiag-reprogram-buick-2008-16 j2534-vxdiag-reprogram-buick-2008-17 j2534-vxdiag-reprogram-buick-2008-18 j2534-vxdiag-reprogram-buick-2008-19

Read the reprogramming instruction.

j2534-vxdiag-reprogram-buick-2008-20

 

Download from the server completed.

Reprogramming completed with J2534 Vxdiag.

j2534-vxdiag-reprogram-buick-2008-21 j2534-vxdiag-reprogram-buick-2008-22 j2534-vxdiag-reprogram-buick-2008-23

 

Done.

Share