How to reset BMW airbag with Carprog v8.21 v9.31
It just takes 1 minute to reset and repair airbag computer in your office, with the new CarProg v8.21 or CarProg v9.31 airbag reset tool. […]
It just takes 1 minute to reset and repair airbag computer in your office, with the new CarProg v8.21 or CarProg v9.31 airbag reset tool. […]
The newest BMW electronic spare parts catalogue ETK 03.1.30 version 2016.11 has been released and shared at forums. Quoted it to share. Free download: […]
Original iKeycutter Condor XC-MINI master series key cutting machine is a famous key cutting machine it can Support many vehicles:Acura, AlfaRomeo, Audi, BMW, Kia, Lancia, […]
Here is a experience from DK forum members who made this possible about how to reflash CARPROG Mcu AT91SAM7S256 Tool use: Carprog clone v8.21 firmware We need […]
Just managed program a NEW REMOTE CENTRAL LOCKING BOARD to the Astra Mk4 WITHOUT ALARMS via OPCOM V1.59. I used: a NEW remote central locking […]
Here are optional user solutions for the Renault can clip v159 was connected to PC, detected with the number 926 573 and recognized ” RLT2002 PROBE”, but CLIP popped an […]
It’s aimed to help use OPCOM v1.59 to set seat belt reminder warning sound status OFF. Purpose: Op-Com set seat belt reminder war ning […]
Scania VCI 2 VCI 3 software has updated to Scania Diagnosis and Programmer 3 SDP3 v2.27. Here is the instruction on how to install / […]
This is our customer meet a problem when he decided to try and make mb star c3 work, but every time he try to communicate […]
It’s verified that only OPCOM OP-COM firmware version 1.39 running with VAUX-COM 2009 software can read security codes for key programming, all tested by users. […]
This VAG PRO support CAN BUS + UDS + K-Line for diagnostics and programming of electronic components used in vehicles Volkswagen, Audi, Seat, Skoda, made from […]
When i installed Xprog-m v5.5.5 software, the Safengine error □□□□ popped up Solved by professional technicians! Open Computer Management and the find out ET199 […]
DAF VCI lite (V1) is the best solution on market, fully replaces DAF VCI560, works with all DAF trucks from oldest till newest EU6, is much […]
Here, OBDexpress released DAF VCI Lite (V1), the replacement of old DAF VCI560, is a cheap but excellent truck diagnostic tool working on all DAF […]
It is a new report from obd2express engineers, of successful mileage adjustment on Volvo s80 ’2008 using OBDSTAR X300 PRO3 key master at :http://www.obdexpress.co.uk/wholesale/obdstar-x300-pro3-key-master.html […]
Received OBDSTAR X300M package for a few days and discussed a lot about it on forums. Sounds an interesting topic. Here share something what i […]
FLY company has newly released OBD Terminator Full Version & Locksmith version with free J2534 DrewTech Software,like Honda HDS, JLR SDD, Toyota TIS, IDS, etc.This […]
Disclaimer: Smart Key Teach-in only supports Mercedes-Benz Smart (1998~2002) with K-line protocol. Smart Key Teach-in support ECU type as follows: MB – Smart vehicles dongle key programmer SMART Teach-in is required when keys are lost, damaged or if additional key is needed. Also, this procedure synchronizes engine ECU with BSI – can be used when changing damagedECU or BSI with new/used one! For adapting each remote with Immobilizer / BSI module the following dongle can be used: 1. Turn ignition ON without starting engine (position “1”). 2. Insert dongle in OBD connector (it is located under steering column, near pedals). 3. The LEDs must lit both, then green must blink few times. If all OK, green LED remains lit and red must be off. If red LED blinks fast, this means an error, you may remove dongle and try again. 4. If red LED is off and green is on, turn OFF the ignition key. 5. Press twice LOCK button on each remote (if 3 button remote used) within 30 sec. Maximum of 4 keys can be programmed. 6. Turn ignition ON again, this completes learning sequence. Remote controls are working only when ignition is OFF, cranking is possible only when vehicle is in UNLOCK-ed state. […]
Here is a customer solution of Carprog v8.21 with the following error message: Unit CRC error: Delete LIB file and make UPDATE -> INTERNET A1 […]
Here’s a real user experience of DIY coding Lambda O2 sensors on BMW E series M5, via BMW K+DCAN INPA cable Tools used: K+DCAN […]
Copyright © 2024 | OBDexpress.co.uk