How To Conduct BMW FEM/BDC Renew Via Copy Data Update On Auro OtoSys IM100

Auro OtoSys IM600 is the Aurodiag the most advanced and smart key programming tool,IM600 based on a 7-inch Android touchscreen tablet that combines the most powerful IMMO and programming functions with OE-level diagnostics and advanced service function

This manual introduces how to conduct BMW FEM/BDC Renew on IM600 via Copy Data Update

Copy Data Update: When the immobilizer information of the vehicle can be read
from the original FEM/BDC module, perform this function to read the information
and write it into the replacing FEM/BDC mdule.

FEM/BDC Renew via Copy Data Update Step-by-step here :

Preparation
1. Attention: If there’s an ELV in the vehicle, the ELV may not be unlocked after
performing FEM/BDC Renew. You’ll need to solve the locked problem yourself, so
please start the operation with careful consideration.
2. To perform the Copy Data Update function, a working key or the engine ISN code is
needed.
3. The hardware version of the original and replacing modules can only vary slightly.
Otherwise, the DTCs of the vehicle may not be cleared.
4. Remove the FEM/BDC module from the vehicle. (See Appendix.)
5. Conduct ECU preprocessing on the replacing (used) module and the original module
to make them able to learn keys. No ECU preprocessing is needed for the replacing
module if it is a brand new one. (Please refer to BMW-A001 for details on ECU
preprocessing.)
6. Prepare a blank key.

2. Procedures
1. Connect the OtoFlash to the original FEM/BDC module via the included main cable.
2. Connect the OtoFlash to the IM600 tablet via USB connection.
3. Turn on the IM600 tablet and tap OtoSys > IMMO. A vehicle menu displays and a
disclaimer prompts up. Tap Accept to continue.

 

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-1(1) BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-2

4. Tap BMW on the vehicle menu.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-vehicle-menu-3

5. Tap ECU Renew > FEM/BDC Renew (CAN).

NOTE
1. You can click the icon near the top-right corner to record the operation data. If you
encounter any difficulties, click the icon again to send us the data and the problem,
so that our engineers could help. The network should be connected when uploading
the data.
2. Please make sure the engine is off before the operation gets started.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-function-menu-4(1) BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-function-menu-5 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-6(1)

6. Tap Copy Data Update, read the notes and procedures listed in the operation guide
carefully, and then tap OK to continue.

NOTE
If you don’t strictly follow the steps, the data may be lost or the FEM/BDC Renew
operation may fail

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-function-menu-7(1) BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-function-menu-8

7. Tap Backup FAFP on the function menu to backup the FAFP data of the original
FEM/BDC module. Read the function information and tap OK to continue.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-9(1) BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-10

8. Tap OK > Confirm to save the data. When a “File saved successfully!” message
displays, tap OK and exit to the function menu.

NOTE
1. The data file can be renamed.
2. Memorize or note down the name and location of the file for later use.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-11 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-12 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-13

9. Tap Read immobilizer data to backup the immobilizer data of the original module.
Read the function information and tap OK to continue

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-14 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-15

10. When a “Do you have a working key?” message displays, make selection
accordingly. Tap Yes and then put the working key close to the emergency start coil
to read the password information, or tap No and move on to read the immobilizer
data

NOTE
If the working key is verified in this step, it can be directly used to start the engine when
the FEM/BDC Renew is completed

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-16 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-17 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-18

11. When the immobilizer data is read successfully, tap Save > Confirm to save the
data. When a “File saved successfully!” message displays, tap OK > Close and exit
to the function menu.

NOTE
1. The data file can be renamed.
2. Memorize or note down the name and location of the file for later use.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-19 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-20 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-21 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-22

12. When Read Immobilizer Data is completed, connect the OtoFlash with the replacing
module via the included main cable.
13. Then tap Write FAFP to write the saved FAFP data into the replacing FEM/BDC
module. Read the function information and tap OK to continue.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-23 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-24

14. Select the saved FAFP data file and tap Confirm to complete Write FAFP. Then tap
OK and exit to the function menu.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-25 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-26

15. Tap Write immobilizer data to write the saved immobilizer data into the replacing
module

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-27 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-28

16. When a module menu displays, make selection accordingly.

NOTE
 New Module: Perform this function if the replacing module is a brand new one.
 Used Module: Perform this function if the replacing module is a used one.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-29

17. Select the saved immobilizer data file and tap Confirm to continue.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-30

18. Tap Write data to ECU. When Write Data to ECU is completed successfully, tap
Close and exit to the function menu.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-31 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-32

19. Tap Repair coding to repair the coding of the new FEM/BDC module. Read the
function information and tap OK to continue

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-33 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-34

20. Tap Yes to continue the coding operation. When Repair Coding is completed
successfully, tap OK and exit to the function menu.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-35 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-36 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-37

21. Tap Key learning to add a key to the new FEM/BDC module. Read the function
information and tap OK to continue.

NOTE
1. The password must be read out before the key can be written or cleared.
2. A key position must be selected before the key can be written or cleared.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-38 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-39 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-40

22. Tap Read password to read the password information of the key.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-41

23. When a “Do you have a working key?” message displays, make selection
accordingly. Tap Yes and then put the original key close to the emergency start coil
to read the password information, or tap No to input the engine ISN code.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-42 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-43 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-44

24. Select a FREE key position and then tap Write key.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-45

25. Follow the instruction to put the NEW key close to the emergency start coil and tap
OK to start Key Learning.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-46 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-47

26. When a “Write Key successful!” message displays, tap OK to check the key ID status.
Then tap Close to exit to the function menu.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100- BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-

27. Tap Reset starter lock to reset the starter lock of the new FEM/BDC module. Read
the function information and tap OK to continue. When this function is done
successfully, Copy Data Update is completed.

BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-50 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-51 BMW-FEMBDC-Renew-on-Auro-OtoSys-IM100-52

28. Install the replacing FEM/BDC module into the vehicle and check if the engine can
be started.

NOTE
1. DTCs may be detected and specific machines are needed for programming, coding
and clear DTC.
2. If the remote function of the original working key doesn’t work after the operation,
please disable the key first and then enable it via Expert Mode > FEM/BDC > Key
enabled/disabled.
3. The newly added keys can be erased if you don’t need them.

Src:http://www.obdexpress.co.uk/upload/pro/im600-bmw-ecu-renew.pdf

 

Share